Browsing by Author "Khan, Irshad"
Now showing 1 - 2 of 2
Results Per Page
Sort Options
- ItemOpen AccessAnalysis and design of a high frequency induction-heating system(2003) Khan, Irshad; Tapson, JonathanAdvances in power electronic semiconductor technology are making high frequency converters for induction heating more feasible at power levels up to 50kW. This research presents the development and analysis of a solid-state induction-heating system, operating directly off single-phase mains frequency, which enables optimum and efficient operation over a frequency range of 80kHz to 200kHz. The system essentially comprises a DC-DC converter configured as a controlled current source, which feeds a load resonant DC-AC inverter, driving a parallel resonant load circuit. The load circuit comprises an induction-heating coil and a reactive power compensating capacitor. The systems active switching elements comprise power MOSFET's but can be extended to almost any other controlled power devices such as IGBT's, BJT's, SCR's, GTO's or SIT's. An automatic frequency control system ensures that the DC-AC inverter drives the load at its resonant frequency, thereby achieving zero voltage switching of the power semiconductors. This operating mode always ensures maximum power transfer to the load as well as maximum operating efficiency of the DC-AC inverter. Driving the load at resonance presents an essentially resistive load to the DC-DC converter, thereby reducing the losses associated with a reactive load. A compact circuit layout combined with this optimum mode of operation eliminates the need for any snubber circuit components in both the DC-DC and DC-AC converters at this power level. An overview into various applications and technologies of induction-heating is presented in this research. A detailed analysis of the induction-heating coil and work- piece are presented in order to aid the design of the load circuit. The induction-heating technology overview presents various induction-heating power sources, discussing the configurations of various topologies. A brief mathematical analysis is used to describe the operation of power electronic converters employed in the induction-heating system developed for this research. The parallel resonant induction-heating load circuit is characterised mathematically, allowing for the determination of the optimum operating conditions. This is followed by a simulation analysis, which is used to gain insight into the problem of frequency control. The frequency control system is modelled and the steady-state error response evaluated under different input conditions. Experimental results on the system implemented, based on operating waveforms and efficiency measurements of the solid-state induction-heating system are presented along with recommendations for future work. The implemented power source was tested at a maximum power of 2.3kW at 151kHz. A system efficiency of 86% at 1.3kW was measured when operating at 138kHz. This design however, provides for scaling to power levels up to 50kW. The induction-heating system's frequency tracking capability is evaluated by heating a steel work-piece through its Curie transition temperature. The induction-heating system is used to heat a 26mm x 35mm stainless-steel billet (work-piece) to 1200°C in 130 seconds using the calculated power of 1.35kW .
- ItemOpen AccessCasting platinum jewellery alloys: the effects of casting variables on fill and porosity(2005) Miller, Duncan; Keraan, Tauriq; Park-Ross, Penny; Husemeyer, Victoria; Brey, Ali; Khan, Irshad; Lang, CandyComparisons are made between platinum-copper and platinum-ruthenium alloys used for jewellery to evaluate the effects of casting variables. The effects of flask temperatures, investments, and centrifugal speeds on microstructure, percentage fill, and porosity were examined over a range of temperatures. Optimum conditions and materials for successful casting of high quality platinum jewellery alloys, using a Hot Platinum induction melting and casting machine, are described. Suitable choice of investment materials and rotational speeds produced good grid fills with Pt-5%Cu and Pt-5%Ru alloys. Metal porosity was more difficult to control, due to the inherently chaotic nature of the casting process, but casting into a relatively cool mould minimised the probability of bad porosity for both alloys. Pt-5%Ru was found to be successful as a casting alloy when used with induction melting technology. It displayed superior uniformity, hardness and colour, compared with cast Pt-5%Cu alloy.